Moisture
Never fire dry
A pull on dry cotton leaves an aftertaste that won't go away. Patience while it soaks pays off.
Advent calendar now open to all To the advent calendar Black November until 22 Nov See the deals
Advent calendar now open to all To the advent calendar Black November until 22 Nov See the deals
€10.10
Manufacturer's recommended retail price: Regular price: €11.90 15% saved compared with the manufacturer's recommended retail priceThis variant is not available
No longer available
Secure payment
Between the big cloud and the calm flavour pull there's a spot where many of us get stuck, and that's exactly where the Geekvape B Series Head with 0.4 ohm sits. It's not a coil for records but one for every day: a Kanthal (KA1) grid, a power window of 25 to 35 watts and a draw that breathes freely without running into thin air. There are five coils in the pack. I set the airflow about a third open, start at 25 watts and tell by taste when it's running cleanly; below you'll also find which devices it belongs in.
B Series · 0.4 ohm
The 0.4 is built for the RDL draw, meaning direct lung with a bit of resistance. You draw into your lungs in one breath and can still feel that a coil is working. For me this is the setting where flavour and vapour volume are most likely to stay in balance.
Spec sheet
Airflow
For the RDL draw I open the air slots about a third. Then the coil draws tight enough for the flavour to gather and freely enough that you're not sucking on a straw. If you open it further, the draw gets airier and moves towards DL, the vapour gets cooler and the flavour a little thinner. If you close it too far, heat builds up in the coil. I work my way in with small turns and take two or three calm pulls after each change before turning further. Your mouth notices the difference faster than any display on the device.
Inside
Inside the 0.4 sits a flat Kanthal grid instead of a wound wire. The surface heats evenly across the whole cotton and carries the flavour calmly and roundly. My advice: let the cotton soak properly before firing for the first time.
Coil change
Switch off the mod and take off the pod or tank. Pour out any remaining liquid before the old coil comes out.
Pull the used coil straight out and press the new 0.4 firmly into the slot without tilting it.
A few drops directly onto the wick windows, then fill. After that I let everything stand for three to five minutes.
I take the first pulls at the bottom end of the window. Then I go up in steps of two to three watts.
Where the flavour is fullest, I stop. I don't go above 35 watts with this coil.
Liquid
A balanced mix around 60/40 (VG/PG) wicks reliably in the 0.4 and still gives plenty of vapour. Very thick liquids with a high VG share take longer to reach the cotton. If you use them anyway, keep the power in the lower range and give the coil a moment between pulls. Heavily sweetened flavours clog any grid faster; that's down to the sugar, not the coil. My rule: the sweeter the tank, the sooner the next coil from the five-pack is ready.
My advice
Moisture
A pull on dry cotton leaves an aftertaste that won't go away. Patience while it soaks pays off.
Replacement
If it tastes dull or slightly burnt, the coil is done. Then I reach for the next one without hesitating.
Slot
The coil needs a B coil slot. A pod with a different slot won't take it.
Devices
The B Series Head comes from Geekvape's Aegis Boost world. It sits in the B60 pod of the Aegis Boost 2 and Aegis Boost 3, in the H45 cartridge of the Aegis Hero 2 and Aegis Hero 5, in the Aegis Force Pod and in the Z Nano 2 Tank. If your pod has a different coil slot, even pressing hard won't help: without the right slot there's no contact, and the mod reports no coil.
Right for you?
If you draw to the lungs but don't need a wall of fog, and if your favourite liquid should taste like itself, you're in the right place. If you want to make serious vapour with the airflow wide open, take a look at the B Series Boost Head with 0.2 ohm. And if you want to go even calmer and with less power, the B Series Boost Head with 0.6 ohm is the more relaxed choice with the same slot.
Questions
Short answers to the most common questions about this item. Your question is not listed? Our customer service is happy to help.
At 25 watts. From there go up in small steps, to 35 watts at most.
It's meant for the loose lung draw (RDL). With the airflow wide open it moves towards DL; the 0.2 is built for the big cloud.
Five B Series Heads, each with 0.4 ohm.
By the taste: if it turns flat, dull or slightly burnt, fit a fresh coil.
Specifications
Customers
Login
Arrived clean
Against my old coils I notice a real difference in flavour. Unpacked them on Tuesday, fitted one straight away and got going. Only after quite a while did the flavour slowly start to fade.
Magda · 28 Jul 2026
Braucht etwas Kraft :)
Mit dem Pack habe ich auch mit meinem Mitbewohner unterwegs immer eine Coil in Reserve. Beim Wechseln sitzt sie anfangs recht stramm.
Jurij · 1 Jul 2026
Voller Geschmack!
Wandert bei der nächsten Bestellung wieder in den Warenkorb. Sauber gefertigt, innen sieht alles ordentlich aus. Seit gut einem Monat kommen die Aromen mit dieser Coil deutlich voller an.
hookah_fan_e · 2 May 2026
GPSR
| Manufacturer |
Shenzhen Geekvape Technology Co., Ltd. 605, Building 1, Qianhai Kexing Science Park, Labor Community, Xixiang Street, Bao'an District 518101 Shenzhen |
|---|---|
| Responsible person |
InnoCigs GmbH & Co. KG |
The 6 brands of this world with the most items.
Advice & knowledge
Tools
Knowledge