Breaking in
Start at 70 watts
A fresh 0.15 ohm coil heats up fast. I give it three fills at 70 watts before going higher so the cotton doesn't scorch on the first pull.
Advent calendar now open to all To the advent calendar Black November until 22 Nov See the deals
Advent calendar now open to all To the advent calendar Black November until 22 Nov See the deals
€11.30
Manufacturer's recommended retail price: Regular price: €14.95 24% saved compared with the manufacturer's recommended retail priceDelivery time 1-3 days
Secure payment
There's that moment when your mod is set above 70 watts, the airflow is wide open and the vapour comes out of the mouthpiece warm and dense. The Geekvape Z Series XM Head with 0.15 ohm is built for that moment. It's the lowest resistance of the standard XM range, a Kanthal mesh coil for 70 to 85 watts in direct lung, five per pack. Before I push it, I check that my mod can hold that power, I break it in at 70 watts, and I only give it thick liquid, because it's pickier than its 0.4 ohm sibling.
Z Series XM · 0.15 ohm
The mesh heats over a large area and evenly, and the vapour turns warm and dense. That has a flip side: the coil drinks more liquid than the 0.4 ohm version and needs a mod that reliably delivers 85 watts. If yours can do that, you get a coil with real character.
At a glance
Device
0.15 ohm isn't a resistance for every device. Your mod should safely deliver up to 85 watts, and not only with freshly charged cells but in the evening too. So I always check first whether the device recognises the low resistance cleanly and holds the set power before I really push the coil. If the display shows a warning or the power drops noticeably, the 0.4 ohm version is the smarter choice for that device. That's not a weakness of the coil, it's simply physics: low resistance needs a lot of current.
Fit
The Z Sub-Ohm Tank, Z Sub-Ohm 5, Z Fli and Z Fli 2 take the coil, as do kits that come with one of these tanks. The Z Nano and Z Max have a different slot. I push it in straight and firmly so the contact sits cleanly and nothing leaks.
My advice
Breaking in
A fresh 0.15 ohm coil heats up fast. I give it three fills at 70 watts before going higher so the cotton doesn't scorch on the first pull.
Liquid
Thin 50/50 liquids wick too fast at 0.15 ohm. Then the coil gurgles or the tank leaks at the airflow.
Airflow
This coil needs air. With the airflow half closed the vapour gets hot and the draw sluggish, so feel free to open it all the way.
Fine-tuning
The jump from 70 to 85 watts sounds small, but at the mouthpiece it's big. At the bottom the coil tastes round and still fairly cool, in the middle of the range the vapour gets noticeably warmer, and just below 85 watts you notice how much liquid it gets through in a short time. I see the dial as a temperament switch: fresh, fruity liquids I like lower down, heavy dessert flavours can run higher up. I never go above 85 watts, that's where the dry, burnt pull the scene calls a dry hit is waiting. And refill before the tank is empty, because mesh running dry doesn't forgive it.
Right for you?
The 0.15 ohm coil is yours if you want lots of vapour, own a powerful mod and like to draw with the airflow open. It suits long evenings with dessert flavours and anyone who wants to really push their Z tank. If you want the same power but to swap coils less often, the Z Series XM Boost Head with 0.15 ohm is the matching counterpart: same resistance, same slot, separate range. If all that is a bit much for you, the 0.4 ohm version of the same family takes the pace down and gets by with 50 to 60 watts.
Questions
Short answers to the most common questions about this item. Your question is not listed? Our customer service is happy to help.
The 0.15 ohm coil needs 70 to 85 watts and delivers more vapour. The 0.4 ohm coil runs at 50 to 60 watts and is easier on liquid and battery.
No, the Boost Heads are a separate range with their own product. Resistance, wattage range and slot are the same; according to Geekvape the Boost lasts longer.
Usually the liquid is too thin. With a liquid from 70/30 VG and the airflow fully open, the coil normally settles down.
As soon as it tastes burnt or noticeably less vapour comes. At 0.15 ohm this happens sooner than at 0.4 ohm, because more liquid passes through the cotton.
Specifications
Customers
Login
Nichts auszusetzen :)
Das Liquid zieht gut nach, auch bei längeren Zügen.
Lina B. · 16 Jan 2026
Ein Volltreffer
Erst nach einer ganzen Weile ließ der Geschmack langsam nach. Ich war vorher nie Kunde hier, das ändert sich jetzt. Meine alten hielten kürzer und schmeckten dumpfer, das is hier anders.
Yasemin · 27 Oct 2025
Easy to prime
Let the coil sit briefly and you get a rounded draw from the start. The parcel got stuck in the sorting centre for a day.
Eren · 10 Sep 2025
GPSR
| Manufacturer |
Shenzhen Geekvape Technology Co., Ltd. 605, Building 1, Qianhai Kexing Science Park, Labor Community, Xixiang Street, Bao'an District 518101 Shenzhen |
|---|---|
| Responsible person |
InnoCigs GmbH & Co. KG |
The 6 brands of this world with the most items.
Advice & knowledge
Tools
Knowledge