Eleaf - iVeni SE Pod - Kit - Black
Delivery Time 1-3 working days
The Eleaf iVeni SE is a slim pod system with a built-in 1100 mAh battery and up to 35 watts. The device automatically adjusts the power to the coil in the pod. The pod holds 2 ml and has a mesh coil that is fixed in the pod. This version has a housing in black.
Battery and power
The battery is not replaceable and charges via USB-C with up to 2 A. The housing measures 109 × 24.8 × 14.7 mm. You do not set the power yourself: the chip reads the resistance of the pod and selects the wattage itself. Protection against short circuit, overcharging and undervoltage is also included.
Pod and coils
The iVeni pods come with 0.4, 0.6, 0.8 and 1.2 ohm. The device works at about 32 W (0.4 ohm), 22 W (0.6 ohm), 15 W (0.8 ohm) and 11 W (1.2 ohm). The pod is transparent, so you can see the fill level from outside. It is filled through an opening with a silicone plug, and the pod stays on the battery device. The coil is part of the pod: if the vapor amount drops, you replace the whole pod.
Operation
The iVeni SE has draw activation: you draw on the mouthpiece and the device fires. A slider on the side controls the air supply. This puts you between a tight MTL draw and a more open RDL. The round indicator on the front shows the battery level in three colours: green, blue and red.
How to get started with the iVeni SE
- Charge the battery via the USB-C port. A cable is not included.
- Open the silicone plug on the pod and fill it to just below the maximum mark. Close the plug again.
- Let the pod stand for a few minutes so that the coil soaks. A dry pod burns.
- Set the airflow slider and take the first puffs short and calm. You do not set the power.
Scope of delivery
- 1 × Eleaf iVeni SE battery device
- 1 × iVeni pod 0.4 ohm
- 1 × iVeni pod 0.8 ohm
- 1 × instruction manual
Frequently asked questions
Can I adjust the power on the iVeni SE?
No. The power follows the resistance of the inserted pod, 35 W at most.
Which pods fit?
The iVeni pods with 2 ml and a mesh coil. They also fit the iVeni Pod Kit.
Is a USB-C cable included?
No, you need your own cable. The port charges at up to 2 A.
How do I tell that the battery is running low?
By the colour of the round indicator. It changes from green through blue to red when the charge is low.
Eleaf
Eleaf is an e-cigarette manufacturer from Shenzhen in China and has been developing devices since 2011. The Hookain Onlineshop carries the iCita and iVeni pod kits together with matching replacement pods.
iCita and iVeni
Both series are refillable pod kits: you fill the liquid into the pod yourself, the coil is built into the pod and replaced with it. The SE versions are separate variants of each series. Depending on the model, filling is from the side (side fill) or from the top (top fill), charging is via USB-C.
Pods with coil
The iCita pods come in packs of two, the iVeni pods in packs of four. Both have the coil already built in, you just insert and fill them.
Which resistance for which draw?
- 1.2 and 0.8 ohm: tight draw into the mouth (MTL, mouth-to-lung)
- 0.6 and 0.4 ohm: open draw with resistance (RDL)
- 0.3 ohm: direct lung draw (DL) at higher power
Beyond the pod kits, Eleaf is known for mods such as iStick and Pico and for the iJust series.
- 1100 and 1400 mAh
battery capacity of the kits - 13 to 40 W
adjustable power - 2 and 3 ml
pod capacity - 0.3 to 1.2 ohm
pod resistances - USB-C
charging at 5 V / 2 A
Do I change the coil on Eleaf pods separately?
No. The coil sits inside the pod, you replace the whole pod.
How do I fill the iCita and iVeni?
Depending on the model, through an opening on the side or on top of the pod.
Which power should I set?
That depends on the pod: high resistances work with few watts, the 0.3 ohm pod with considerably more.
Where does Eleaf come from?
From Shenzhen in China. The brand has been developing e-cigarettes there since 2011.
| Age Rating: | 18+ |
|---|---|
| Battery Capacity: | 1100 mAh |
| Charging current: | DC 5V/2A |
| Color: | Black |
| Connection: | USB C |
| Device family: | Eleaf iVeni |
| Device type: | Refillable |
| Draw type: | MTL (Mouth-to-Lung), RDL (Restrictive-Direct-Lung) |
| Filling Type: | Side Fill, Top Fill |
| Filling Volume: | 2 ml |
| Part: | Device |
| Power: | 35 W |
| Resistance: | 0.4 Ohm, 0.8 Ohm, 1.2 Ohm |
Login
Compatible With
Compatible With
