Vaporesso - Vibe - Dual - Mesh Pod - 0.7 / 1.0 Ohm - 2 Pcs.
Available soon - sign up to get notified
The Vaporesso Vibe Dual Mesh pod with 0.7/1.0 ohm is the gentler version of the replacement pod for Vibe and Vibe SE. The pack contains 2 pods, each with a 4.5 ml tank, side filling and two built-in mesh coils. It is intended for a tighter draw with less power.
1.0 ohm for ECO, 0.7 ohm for power
You choose the mode on the device and the pod follows. In ECO mode the 1.0 ohm coil works: low power, economical battery use and a tight draw towards MTL. In Power mode the 0.7 ohm coil takes over, the vapor gets fuller and the draw somewhat looser. The device sets the wattage itself for each mode.
The version with 0.6/0.8 ohm delivers more power and a looser draw.
Which devices fit
The pod fits the Vaporesso Vibe SE and the Vaporesso Vibe and clicks in magnetically. The Vibe SE 2 uses the Vibe Dual Mesh Smart pod, which is filled from the top.
Replace and fill the pod
- Pull the pod off the device.
- Uncover the side opening, fill the pod to just below the maximum mark and close it again.
- Wait a few minutes so that the cotton saturates.
- Insert the pod and start in ECO mode. Fired dry, the coil burns.
Scope of delivery
- 2 × Vibe Dual Mesh pod 0.7/1.0 ohm, 4.5 ml each
Frequently asked questions
Is the 0.7/1.0 ohm version more for MTL?
Yes. In ECO mode with 1.0 ohm it draws tighter than the version with 0.6/0.8 ohm. In power mode the draw becomes looser.
Can the coil be replaced individually?
No, the windings are built in. The complete pod is always replaced.
How is the pod filled?
From the side, through an opening with a silicone closure. For this you pull the pod off the device.
Vaporesso
Vaporesso has been building e-cigarettes since 2015: refillable pod kits such as XROS and ECO, battery mods from the Luxe and Armour series and the Dojo devices with a prefilled pod. Matching coils, empty pods and tanks are available too.
Which Vaporesso series matches your draw
| Series | Type | Draw |
|---|---|---|
| XROS, ECO Nano, ECO One, Vibe | Pod kit with refillable pod | MTL or RDL |
| Luxe X, Luxe XR, Armour | Kit or mod with large pod or tank | RDL to DL |
| Dojo Blast X, Dojo Twist | Device with prefilled pod | MTL |
RDL (restrictive direct lung) sits between MTL and DL: the draw goes straight to the lungs, but with more resistance than an open DL draw. Which level a device handles is set mainly by the coil resistance.
Luxe XR: pod with GTX coil
The Luxe XR kits take pods with a replaceable GTX coil. At 0.2 to 0.4 ohm the draw is more open, at 0.6 to 0.8 ohm tighter.
- USB-C
charging at 5V / 1A or 5V / 2A - 950 to 3200 mAh
battery capacity from small pod kit to mod - 5 to 100 W
power range of the adjustable devices - 0.15 to 1.2 ohm
coil resistances - Top, side, bottom fill
filling from the top, the side or below
Which coil fits my Vaporesso?
The Luxe devices use GTX coils, the XROS kits their own XROS pods with a built-in coil. The matching device is part of every coil name.
What is the difference between Dojo and XROS?
Dojo pods come prefilled and are replaced as a whole. XROS pods are filled with liquid yourself.
Can I adjust the power?
On mods such as Armour and Luxe, yes, from a few watts up to 100 W. Simple pod kits set the power themselves via the pod.
How do I charge Vaporesso devices?
All current kits charge via USB-C; a cable is included.
Manufacturer
Shenzhen Smoore Technology Limited
Building 8, Dongcai industrial Park, Gushu Town, Baoan District, Shenzhen, China. 518102
support@vaporesso.com
Responsible Person
InnoCigs GmbH & Co. KG
Barnerstr. 14b 22765 Hamburg
service@innocigs.com
| Age Rating: | 18+ |
|---|---|
| Device family: | Vaporesso Vibe |
| Draw type: | MTL (Mouth-to-Lung) |
| Filling Type: | Side Fill |
| Filling Volume: | 4,5 ml |
| Part: | Empty pod |
| Resistance: | 0.7 Ohm, 1.0 Ohm |
Login
Matching Products
Matching Products
