€12.90
Manufacturer's recommended retail price: Regular price: €13.90 7% saved compared with the manufacturer's recommended retail priceThis variant is not available
No longer available
Secure payment
Not everyone who vapes direct lung wants to crank their mod to the limit for it. The Geekvape Z Series XM Head with 0.4 ohm is made for exactly these people. It's the calmest coil of the XM range: Kanthal (KA1) mesh, built for 50 to 60 watts, five in the pack. It fits every tank with a Z coil slot and gives you an open DL draw without your device having to dig into its reserves. I run it on thick liquid from 70/30 VG, start at 50 watts, and when I want denser clouds I reach for one of the 0.15 ohm coils.
Z Series XM · 0.4 ohm
The relaxed XM: direct lung at 50 to 60 watts
At 0.4 ohm the coil stays in the middle power range of your mod. The vapour comes a little cooler and less dense than with the 0.15 ohm coil, but a tank fill lasts longer and so does the battery charge. For many single-battery mods, this is the resistance they're most comfortable with.
- Resistance 0.4 ohm
- Power 50–60 W
- Coil wire mesh, KA1
- Contents 5 coils
Spec sheet
The 0.4 ohm coil in numbers
- 0.4 Ω resistance, mesh
- 50–60 W wattage range
- 5 pieces coils per pack
- Z coil slot in the tank
Fit
Which tank it belongs in
The coil fits the Z Sub-Ohm Tank, the Z Sub-Ohm 5, the Z Fli and the Z Fli 2, so also kits that come with one of these tanks. For the Z Nano and Z Max you need different coils. Take a quick look at your tank first, and the swap works the first time.
Liquid
What I fill the tank with on the 0.4 ohm coil
Mesh coils of this size like thick liquid. On the 0.4 ohm coil I use liquids from around 70/30 VG, so the cotton wicks fully without the tank sweating. Thin 50/50 mixes aren't meant for this design: they flow through too fast, moisture collects at the airflow, or it gurgles on the draw. If you like switching flavours, do it together with the coil change, because a strong liquid lingers in the cotton for quite a while. For me, a fresh coil for a new favourite liquid is the most honest way to get to know it.
Step by step
How I fit the 0.4 ohm coil
-
Remove the tank
Switch off the mod, take off the tank and empty it. I take out the old coil and wipe the contact surface in the base dry.
-
Prime the cotton
Put a few drops of liquid into the openings of the new coil until the cotton turns visibly darker.
-
Fit it straight
Push the new coil in straight and firmly, reassemble the tank and fill it.
-
Let it soak
Wait at least three to five minutes. I'd rather give it ten, the cotton rewards you with clean flavour from the first pull.
-
Start at 50 watts
Take the first pulls at 50 watts and only then move up towards 60 watts in small steps.
Finding the power
Between 50 and 60 watts: how I work my way in
I start every new 0.4 ohm coil at the bottom end, at 50 watts, and give it the first two or three fills. Then I turn it up in two-watt steps until the vapour arrives warm but not hot. For me that usually lands somewhere in the middle of the range. Above 60 watts the vapour gets sharp and hot, and the cotton gives up sooner than you'd like. With this coil you can set the airflow a bit tighter than with the 0.15 ohm coils. Half closed gives a restricted, loose draw somewhere between classic direct lung and RDL that many find rounder.
Choosing resistance
0.4 ohm or 0.15 ohm?
| What to expect | 0.4 ohm | 0.15 ohm |
|---|---|---|
| Wattage range | 50 to 60 watts | 70 to 85 watts |
| Vapour | a little cooler, less dense | warm and dense |
| Consumption | less liquid and battery | more liquid |
| Mod | many single-battery devices too | must reliably deliver 85 W |
Both sit in the same Z coil slot, so you can switch at any time.
Right for you?
Who the 0.4 ohm coil is right for
If you like direct lung but don't need a cloud like a fog machine every time, the 0.4 ohm coil is yours. It suits you if you're out and about with a compact mod, if your tank should last a whole day or if you're just getting into direct lung. If you want it denser and warmer, take a look at the Z Series XM Head with 0.15 ohm. And if you vape a lot and want to swap coils less often, the Boost coils such as the Z Series XM Boost Head with 0.2 ohm are a separate range with the same slot.
Questions
Questions about the Z Series XM Head 0.4 ohm
Short answers to the most common questions about this item. Your question is not listed? Our customer service is happy to help.
Are 50 watts enough for the 0.4 ohm coil?
Yes, 50 watts is the bottom end of its range. You can turn it up to 60 watts to taste.
Does it fit my Z Fli 2?
Yes. Z Fli, Z Fli 2, Z Sub-Ohm and Z Sub-Ohm 5 take it, but the Z Nano and Z Max don't.
Can I swap it for a Boost Head?
Yes, the slot is the same. But reset the power after the swap, because the Boost coils only start at 70 watts.
How do I know the coil is used up?
The vapour tastes burnt, the flavour goes flat or the vapour volume drops. Coils are wear parts, which is why there are five in the pack.
Specifications
Technical details
Customers
Reviews
Login
Ausdauernde Coil
Im Vergleich zu anderen Coils, die ich hatte, macht diese deutlich länger mit.
Jens N. · 27 Aug 2026
Thumbs up
I'm really glad I bought it. I don’t vape much, so a coil lasts longer for me anyway. Arrived intact and clean, as it should. Even on the terrace I can swap the coil without any trouble.
Leyla K. · 14 May 2026
Sauber angekommen
Top Eindruck von Anfang an. Praktisch, dass gleich 5 dabei sind, so habe ich immer Ersatz in der Schublade. Beim Öffnen machte alles einen frischen, sauberen Eindruck.
Michael Nasser · 14 Mar 2026
GPSR
Manufacturer & responsible person
| Manufacturer |
Shenzhen Geekvape Technology Co., Ltd. 605, Building 1, Qianhai Kexing Science Park, Labor Community, Xixiang Street, Bao'an District 518101 Shenzhen |
|---|---|
| Responsible person |
InnoCigs GmbH & Co. KG |
More Vape brands
The 6 brands of this world with the most items.

